Hey everybody! It’s Ceal, here. Today I am sharing a card using a technique that I am calling “faux watercolor” because the end result look like it was water colored to me.
Skill: Beginner Time: 30 minutes
Directions:
Start by gathering your supplies. You will need a A2 card base, a white panel, a panel of tidepool cardstock, several colors of VersaMagic ink, VersaFine Clair Pinecone ink, Memento Tangelo ink, sponge daubers and an embossing folder.
Step 1: Make a dry run of the embossing folder through the die cutting machine.
Step 2: This looks like a hot mess, but I promise it gets better. Using a sponge dauber, color the leaves as desired using VersaMagic inks.
Step 3: Lock the embossed panel back into the folder and generously ink up the debossed side with a dark brown ink. Close the folder and run it through the die cutting machine.
Step 4: Glue the panel down on the card base and add a sentiment. I used a happy birthday die cut.
Hello! I’m Alison Heikkila. The weather by me has been really beautiful, and it’s enhanced by the changing colors of the leaves. I decided to pull out a few Kaleidacolor Ink Pads and my 5×7 Gel Press Plate and show you how easy and fun it can be to make prints with different types of foliage.
*Some affiliate links are used in this post. That means that if you shop through these links, I may receive a small compensation, at no cost to you. For more information, please see my Affiliates page, where I also have some coupon codes.
Skill Level: Basic Time to Complete: As long as you feel like playing!
I didn’t want to stop making prints! This process can be very addicting. I hope you give it a try and find it fun and relaxing. Thanks so much for stopping by. Have an inspiring day!
Intro: Here’s an embossed shimmery shaker card created with a Kaleidacolor Inkpad, several Memento Dew Drop Inkpads, and a Golden Glitz Delicata pad.
Skill Level: Beginner to Intermediate
Time: 1.5 hours
Step 1.
Place the square mini Gel Press onto an acrylic block.
Step 2:
Open the Autumn Leaves Kaleidacolor pad, Press the mini Gel Press against the pad, slide the Gel Press down to fill the Press with ink.
Step 3:
Flip the acrylic block so that the inked Gel Press is facing upward. You’ll notice that the paper is not straight. It’s good to apply the ink in a random pattern. Place a piece of white cardstock against the Gel Press and pull the print.
Repeat Step #2 and Step #3 until the paper is covered with ink.
Repeat Steps #2 and 3 again to create a second print.
Step 4:
Spray the print (which looks like a hot mess at this point) with 91% Isopropyl Alcohol until the paper is saturated. Heat set.
Step 5:
Coat both prints with Purell to further lighten and blend the colors. A side benefit is that your hands will get clean!
Step 6:
Mist the prints with water to add some droplets and white splatter. Heat set.
Step 7:
Use Sponge Daubers to yellow from the Kaleidacolor pad, New Sprout, Bamboo Leaves, Sugar Plum, Dandelion, Tangelo, Lady Bug, Rhubarb Stalk, Ladybug, and Lilac Posies to enhance both prints.
Step 8:
Spray the prints again with 91% Isopropyl Alcohol. Heat set and flatten the prints if necessary.
Step 9:
Place a print inside the embossing folder and run it through a die-cut machine.
Step 10:
Use a leaf die to cut the embossed print. Reserve the leaf for another use.
Step 11:
Apply Golden Glitz Delicata to the edges of the leaf window and the panel.
Lightly tickle the embossed elements to add some glittery golden touches to the design.
Heat set.
Step 12:
Flip the embossed print. Take a second to admire the colors of the reverse. The ink colors change and meld somewhat due to the Isopropyl Alcohol.
Place Tear It Tape around the edges of the leaf on the back of the panel. Secure a piece of acetate to the tape on the panel.
Step 13:
Place foam tape around the edges of the leaf to create a well for the shaker contents. Be sure that there are no gaps between the pieces of tape. Use an embossing buddy or a dryer sheet to gently rub the sides of the tape and the acetate window so that the shaker contents can be move freely.
Fill the aperture with your selection of shaker contents.
Carefully pull the backing off of the foam tape and place a piece of cardstock over the aperture to seal the shaker.
Step 14:
Use cutting dies to cut rust cardstock (not shown).
Apply Golden Glitz Delicata Ink to the die-cuts.
Step 15:
Adhere the sentiment below the shaker element.
Step 16:
Use Tear It! Tape to adhere the front of the shaker card to an A2 Rust card.
Hello friends! This is Linh (or LV Handcrafted on all the socials). Today I have a new video up on the Imagine Crafts YouTube channel showing how to create easy ombre papers to die cut from. The easiest way is Kaleidacolor ink pads! Just swipe and you’re done! Just as simple though is to swipe VersaMagic ink across your cardstock. I like using a small blending brush to create a smooth transition from one color to the next. Whichever method you prefer, the results are stunning!
Hello there! Today’s tutorial is to show you how easy is create texture with Memento Inks. This is a very simple process that you can create with a score lines and or embossing folders. On this card, I used Memento Ink Desert Sand, Peanut Brittle and Teal Zeal.
Imagine Blog 